Do not remember me!

### Categories

We have Tested and found Below Host Trustable, Please Buy Premium account From Below Host.

Note: Do not Buy Premium account from Reseller

» » » Fundamentals of Electrical Instrumentation

## Fundamentals of Electrical Instrumentation

MP4 | Video: h264, 1280x720 | Audio: AAC, 44.1 KHz, 2 Ch
Genre: eLearning | Language: English + .srt | Duration: 38 lectures (1h 44m) | Size: 918.3 MB

Master the fundamentals of instrumentation: Learn to wire digital & analog circuits and understand how they work!
What you'll learn:
Instrumentation wiring & operation
Digital (discrete) Inputs - learn digital input circuits, learn how to wire contact and transistor input devices in sink & source configuration
Digital (discrete) Outputs - learn digital output circuits, learn how to wire output devices such as a solenoid actuated valve, learn sink & source output wiring configuration
Analog Inputs - learn 0-10volt and 4-20ma input circuits, learn how to connect a loop powered analog input device
Analog Outputs - learn 0-10volt and 4-20ma output circuits, learn how to connect a current output to a variable frequency drive
Requirements
Understand the difference between AC and DC
Understand difference between Normally Open & Normally Closed
Understand basic ohms law theory
Understand basic electrical circuit principles for e.g. current flow, voltage potential, and series & parallel circuits
Understand the purpose of instrumentation - not critical
Understand what a transistor is - not critical
Description
In this course you will learn the Fundamentals of Electrical Instrumentation - you will learn about the different types of devices, sensors, and circuits used in this field.
Instrumentation is the vital ingredient that enables the process control systems of buildings and factories to run smoothly. Within these process control systems are numerous instrumentation devices that take measurements and perform operations which are transmitted and received via electrical circuits - in other words along the wires that they are connected to!
It takes a skilful person to know how these electrical circuits work and how the wiring must be connected. That's where you come in!
After completing this course, you will know how to wire up digital (discrete) & analog instrumentation devices and understand how the electrical circuits connected to them work.
Electrical instrumentation devices come in many forms, the four types that we will focus on in this course are:
-Digital (discrete) Inputs
-Digital (discrete) Outputs
-Analog Outputs
In the course we will start off by looking at Digital Inputs, we will learn about what digital input devices are used for and learn how to connect them to a controller in sink and source configuration. Connecting a push button and a proximity sensor as digital input devices will be demonstrated.
Digital Outputs are covered next, we learn how to connect a solenoid actuated water valve as an output device and also look at sink and source wiring configurations.
About halfway through the course we put what we've learnt to the test by surfing the net and studying some various wiring diagrams of instrumentation & plc circuits.
When we get to Analog Inputs, we hone in on the basic fundamentals of analog circuits such as the 0-10volt and 4-20ma circuits. We then discuss 2, 3, 4 and 5 wire transmitters and round out the chapter by demonstrating a temperature sensor connected in a loop as an input device. WARNING - there may be a little maths involved (just a little)!
An Analog Output circuit is demonstrated next by using a variable frequency drive as our output device, we get to see what happens to a motor connected to the drive when the analog signal is changed.
To finish off we study a controller as it would look in a real installation with various inputs and outputs connected to it.
So if you are ready to boost your electrical control skills by learning the fundamentals of instrumentation I'll see you in the course!
But don't forget your pen and paper as there will be some fun exercises along the way!
Who this course is for
Anyone that has an interest in instrumentation & PLC wiring and circuitry
People who have done some basic electrical or electronics theory and wish to up-skill
Technicians wishing to learn more about instrumentation wiring & operation
Anyone interested in learning about digital inputs and outputs
Anyone interested in learning about analog inputs and outputs - 4-20ma & 0-10volt
Anyone interested in learning about instrumentation devices and sensors